halloween Jack o lantern pattern | Debosser | (Embosser & Cutter)

Included: One fondant stamp(Outbosser)

Size: The size of the print is 2.5x2.5 inches, 3.5 inch 3.5, or 4.5x4.5 

PICTURED IS 2.5 inch

Acrylic Fondant Debosser

Create beautiful, detailed fondant accents for your cakes, cupcakes, cookies & more! 🎀 Each debosser is made to order in-house by Saida’s Sweets Supplies.

WHAT'S INCLUDED

One acrylic fondant debosser/stamp.

SIZING

Sizing depends on the size option selected at checkout.

Debosser Only:
The size selected refers to the approximate size of the etched design/impression.

Acrylic Plate Size:
The acrylic plate will be sized appropriately for your selected design. It will either be made large enough to accommodate the matching cutter or approximately 1" larger than the etched design, depending on the option selected.

Because each design and cutter shape is different, the overall acrylic plate dimensions may vary.

MATERIAL

Debosser is made from 6mm acrylic.

If a matching cutter is purchased, the cutter is 3D printed using PLA.

HOW TO USE

For best results, lightly dust your fondant or gum paste and/or the debosser with cornstarch or icing sugar to help prevent sticking.

1. Roll your fondant or gum paste to your desired thickness.
2. Place the debosser etched-side down onto the fondant.
3. Press firmly and evenly across the entire design.
4. Carefully lift the debosser to reveal your impression.
5. Brush away any excess cornstarch or icing sugar with a clean, soft brush.
6. If you purchased a matching cutter, position it around the impression and cut out your finished piece. It's now ready to add to your cake, cupcakes, cookies, or other treats! 🤍

✨ Want a deeper impression?

Roll your fondant slightly thicker than usual. Place the fondant directly on top of the etched side of the debosser, then use a rolling pin to roll over the fondant in one firm, even motion.

Gently peel the fondant away from the debosser to reveal a deeper, more defined impression.

Please Note: This debosser is intended for use with fondant, gum paste, and similar soft modeling mediums. It is not intended to be pressed directly into buttercream or icing.

CARE INSTRUCTIONS

Please handle your acrylic debosser with care to keep it looking its best. 🤍

Hand wash using warm, soapy water and a soft sponge or cloth. A small, soft-bristled brush may be used to gently clean detailed or etched areas.

Allow to air dry or gently dry with a soft cloth.

DO NOT place acrylic debossers in the dishwasher. High temperatures may damage or warp the product. Avoid abrasive scrubbers or harsh cleaning products, as acrylic can scratch.

3D-Printed Cutters: Hand wash only using cool, soapy water and allow to air dry. Cutters are NOT dishwasher safeand should be kept away from heat.

PROCESSING TIME

All items are made to order.

Current processing times can always be found in the announcement banner at the top of our website, as processing times may change depending on order volume, sales, and holidays.

Please check the current processing time before placing your order, especially if you are ordering for a specific event date. 🤍

SHIPPING DISCLAIMER

Please keep both our processing time and the shipping carrier's estimated transit time in mind when placing your order.

Once your package has been accepted and scanned by the shipping carrier, Saida’s Sweets Supplies is not responsible for delays, lost packages, stolen packages, or packages marked as delivered by the carrier. Shipping and delivery dates provided by the carrier are estimates and are not guaranteed unless otherwise stated by the shipping service purchased.

Please double-check that your shipping address is complete and correct before placing your order. We are not responsible for packages delivered to an incorrectly entered address.

If your tracking shows a delay, loss, or delivery issue after the package has been accepted by the carrier, please contact the shipping carrier directly for additional assistance.

If your order arrives damaged due to an issue with the product itself or you received an incorrect item, please contact us so we can help. 🤍

PLEASE NOTE

Each item is made to order in-house by Saida’s Sweets Supplies. Small variations may occur between products.

Colors of 3D-printed cutters may vary depending on filament availability.

Due to the made-to-order nature of these products, please carefully review your design, size, and selected options before completing your purchase.

Thank you so much for supporting my small business! 🎀🤍